How to Install a Ghost Immobiliser
Ghost immobilisers protect your vehicle from key cloning or hacking. It works by stopping the engine from running until a PIN code has been entered. It can be as long as 20 characters.
It is not detected by thieves who don't expect this extra layer of security. Certain systems come with an app which allows the owner to deactivate their immobiliser in the event of forgetting their PIN number or utilize the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser, a cutting edge security system, can be incorporated directly into the ECU of your vehicle. It provides a discreet protection against thieves. It is highly efficient and user-friendly and is a great option to add to your vehicle's security arsenal. But, as with any other anti-theft device, it is not foolproof and requires regular maintenance to ensure its operation. Luckily, this guide will aid you in getting the most value from your Ghost 2 Immobiliser.
CAN (Controller Area Network), a robust serial networking, allows microcontrollers communicate with each over short distances. Central control units is not required. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It has many advantages, including low cost and easy use.
In most modern cars In modern cars, the CAN protocol is used to communicate with various systems, including the engine management system (EMS) steering module, transmission controller air conditioning controls, and many more. It also transmits sensor data, such as speed sensors, as well as other inputs, in order to control the various features of the car. The CAN bus is used to monitor these diverse components, and can prevent a vehicle from starting if they're in danger of failure.
While the CAN bus could be utilized for a variety of purposes, it's important to understand how it works and how it's secured. It is possible to add new features to a vehicle using CAN bus, but it's important to secure it against attacks from hackers and other dangers. ghost 2 immobiliser review to accomplish this is to install firewalls and monitoring your CAN bus through software.
Ghost2's discreet control unit is hidden away in the car's wiring harness or dashboard, eliminating the possibility of a criminal physically tampering with it. It's also impossible to reset the PIN code or emergency code without access to the vehicle.
You can activate Transport Mode If you need to give your vehicle away for valet parking, service or for any other reason. This feature turns off both the keyfob and the ignition functions of the Ghost immobiliser. It will only reactivate after the car has reached 31 mph over a period of 15 minutes.
How to create a PIN code
The Ghost immobiliser protects your car from theft. The latest technology utilizes a PIN code to shut down the engine and stop it from running without the correct code or a valid fob/mobile device. The system's sleek design makes it unnoticeable, and offers unrivaled security against theft. The system is TASSA-certified and could save you substantial amounts on your car insurance.
During the installation during installation, the Ghost system goes into a learning mode to record the sequence of buttons pressed to generate your unique pin code. After the pin code is created and the installer has completed its work, it will guide you through the process of activating the system. Once activated the Ghost system disables your vehicle's starting motor until you enter a valid PIN or switch the vehicle into transport mode. This makes it very difficult for thieves to duplicate or hack into your vehicle's start system.
Installing an Ghost immobiliser is straightforward however it is essential to follow the precise instructions in the user manual to ensure that it operates properly. Hand tools and multimeters can be used to check electrical values. Insulation tape, heat shrink tubing, and cable ties can be utilized to shield wires from damage. Check the system on a regularly basis to detect any issues that could be.
Once the installation is complete after the installation is complete, you must perform a final check of the system prior to turning on your vehicle's ignition. The Ghost immobiliser will re-arm itself after a period of 3 to 30 seconds, based on your car's model. The system is also equipped with a Service/Valet mode that lets you temporarily disable the system for servicing or valet parking.
Ideally, the immobiliser should be hidden in an inconspicuous location under the dashboard or steering wheel. Use a small amount of duct tape or paint over the wires CAN H and L to make them easier to locate when you are testing. The CAN H and the L wires should be connected to an electrical source that delivers an uninterrupted 12V. It is also essential to check the connections following testing, since misidentifying these wires can cause the system to malfunction.
Invoking the system
A ghost immobiliser prevents your car from starting when you press certain buttons in the vehicle, usually on the steering wheel or door panel, or the central console. The sequence can be altered by the user at any time. Once activated, the system cannot be removed. This is a fantastic option for those who want to safeguard their vehicle against theft.
The system is designed not to be detected by modern diagnostic tools and code-grabbing technologies. It doesn't emit radio frequencies either, making it even more difficult for thieves identify.
If the device is detected, it will prevent the engine from running and sound an alarm that is loud enough to scare away the thief. The device can be used to monitor a car's location which can help police recover the vehicle in case it has been taken.
Contact Car Specalist Customs for a estimate or to discuss your options if you're interested in Ghost immobiliser. We are fully trained to install a ghost immobiliser for your vehicle and will make sure it is hidden in a difficult-to-access area. We can also provide other security measures like the wheel lock and kill switch to help keep your car safe from thieves.
Disarming the System
If you own a Ghost immobiliser that is fitted to your vehicle, it's important to know how to disarm it. It can be used in the event that you lose your keys or your battery is dead. The system utilizes a unique PIN code that only you know, so the immobiliser will not start your car without entering this code. The simplest method to enter the code is to press a set of buttons on your dashboard or the steering wheel. This is much easier than using a key fob, and stops others from copying your remote.
Unlike some aftermarket immobilisers that require cutting wires for installation, Ghost2 is non-invasive and is compatible with your vehicle's bus network to function. Its most notable feature is that it bypasses the engine without affecting vehicle functions. This makes it extremely difficult for thieves to use signal boosts or clone car keys. It doesn't emit radio frequency, therefore thieves won't be able to detect it.
The Ghost system also features an option called Transport Mode that allows you to temporarily disable the security system in circumstances like transportation or servicing. This feature is ideal for when you're loaning your vehicle out to someone else, without sharing your PIN code or if your vehicle requires to be secured while you drive it. Press the service button five times over 2 seconds to activate the Transport Mode. The Ghost system will confirm activation by 5 indication signals.
Save the emergency code outside your vehicle in a secure location. If you happen to encounter a situation where you are locked out of your vehicle, contact the technician or the company that installed the system and they will give you the code. If you are unable reach them, then you can call an authorized dealer. However, this could require verification procedures, and you could be charged additional charges.
This system is not only practical, but it can also safeguard your vehicle from theft and lower insurance costs. Many insurance companies offer lower monthly rates or even financial incentives for installing this anti-theft device.