How to Install a Ghost Immobiliser
A ghost immobiliser protects your vehicle from key cloning and hacking. It stops the engine from running until a PIN number is entered. It can be as long as 20 characters.
It is not detected by thieves and they are unlikely to think about this additional layer of security. Some systems also have an application that allows owners to disable the immobiliser if they forget their PIN code, or to use the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is a cutting-edge security system that is able to be integrated into your vehicle's ECU offering a secure line of defence against thieves. It is highly efficient and user-friendly and is a great addition to your vehicle's security arsenal. But, as with any other anti-theft device, it's not 100% reliable and requires regular maintenance to ensure its operation. This guide will help you get the most of your Ghost 2 immobiliser.
CAN (Controller Area Network) is a reliable serial networking that allows microcontrollers to communicate with each other over short distances. Central control units is not required. It is designed for multiplexing electrical wiring in vehicles to cut down on copper and has a number of advantages, including low cost and a simple use.
In most modern cars, the CAN protocol is used to communicate with a variety of systems, including the engine management system (EMS) transmission controller, steering module air conditioning controls, and many more. It also carries sensor data like speed sensors and inputs, to control various features of the vehicle. The CAN bus can be used to monitor the status of these different components. It could stop the vehicle from starting when it is in danger of failure.
It is important to understand how the CAN bus works and how it's secured. The CAN bus is an excellent way to enhance the features of your vehicle, but it's essential to protect it from hackers and other threats. Installing a firewall, and monitoring your CAN-bus with software is the best method to accomplish this.
Ghost2's control unit is hidden inside the car's wiring harness or dashboard, which eliminates the possibility of a burglar physically tampering with it. It is also impossible to reset a pin code or an emergency code without having access to the vehicle.
You can turn on Transport Mode if you need to sell your car for service, valet parking or for any other reason. This feature disables both the keyfob and the ignition functions of the Ghost immobiliser. It will only be activated after the car has reached 31 mph for a period of 15 minutes.
How do I create a PIN code
The Ghost immobiliser guards your vehicle from thieves. The revolutionary technology utilizes the PIN to shut down the vehicle's engine and prevent it from starting if you don't have the correct code, or a valid fob/mobile. The system's discrete design is unnoticeable and also provides unbeatable protection against theft. Additionally, the system is TASSA verified and can provide significant savings on insurance premiums for cars.
During installation, Ghost enters a "learning mode" to record the sequence of buttons pressed in order to generate your unique pin codes. The installer will guide you through activating the system after the pin code has been created. Once activated, the Ghost system will turn off your vehicle's starter motor unless a valid PIN is entered or the vehicle is switched into transport mode. This makes it extremely difficult for thieves or cloners who want to hack or clone your vehicle's starter system.
It is simple to install an easy-to-install Ghost immobiliser, but you must follow the detailed instructions in the user's guide to ensure the proper operation. Basic hand tools will assist in making precise connections and a multimeter can aid in checking the electrical value. Insulation tape and heat shrink tubing can shield the wire from damage and cable tie is essential to keep everything neat and secure. Also, be sure to test the system frequently to spot any potential issues and mistakes.
After the installation is completed it is crucial to make a final test of the system before switching on the ignition of your vehicle. Ghost immobilisers will re-arm themselves after a period of 3 to 30 seconds, depending on the model of your car. The system also has a Service/Valet mode that allows you to temporarily remove the system for servicing your vehicle or valet parking.
Ideally, the immobiliser should be concealed in a hidden location beneath the steering wheel or on the dashboard. It is recommended to use a small piece of duct tape or paint to mark the CAN H and CAN L wires so that you can easily locate them during testing. The CAN H and the L wires must also be connected to an electrical source that delivers a constant 12V. It is also essential to check the connections following testing, as a mistake in identifying these wires can cause the system to malfunction.
The system must be activated
A ghost immobiliser stops your car from starting until you press a few buttons in the vehicle, usually on the steering wheel or door panel, or the central console. The sequence is determined by the user and is able to be changed as needed. Once activated, the system will not be turned off. This makes it an ideal choice for anyone looking to protect their vehicle from theft.
The system is not designed to be detected by modern diagnostic tools and code-grabbing techniques. It also does not send radio signals which makes it harder for thieves to detect the device.
If the device is identified, it will stop the engine from starting and sound an alarm that is loud enough to scare off thieves. The device can be used to monitor a car's location which can assist in the recovery of the vehicle in case it has been stolen.
If you're interested in a ghost-immobiliser call the experts at Car Specalist Customs to get a quote and discuss your options. We are qualified to install ghost immobilisers for your vehicle. We will make sure that it is placed in a location that is difficult to reach. We also offer other security measures such as an ignition lock for your wheel and a kill switch to help keep your car safe from thieves.
Disarming the system
It is essential to know how to deactivate a Ghost immobiliser if it is installed on your car. This will help you in the event that you lock your keys in the car or if your battery dies. The system has a unique PIN code that only you know. It won't be able to start the vehicle without this code. Pressing the combination buttons on the steering wheel or on the dashboard is the most efficient method to enter your code. This is much easier than using a key fob, and stops others from copying your remote.
Unlike some aftermarket immobilisers that require cutting wires to install, Ghost2 is non-invasive and integrates with your vehicle's CAN bus network to operate. Its most notable feature is that it shuts off the engine, without affecting normal functions of the vehicle. This makes it extremely difficult for thieves to use signal boosts or to clone keys for cars. It does not emit radio frequency, therefore thieves cannot detect it.
ghost 2 immobiliser cost has an option called Transport Mode which allows you to temporarily disable the security system in situations such as transportation or servicing. This is a great option when you have to lend your vehicle to a person who isn't sharing the PIN code, or if you want to keep your vehicle secure while driving it. To activate Transport Mode you need to press the service button 5 times within a period of 2 seconds. The Ghost system will confirm activation with 5 indication signals.
After you're done, make sure to save the emergency code in a secure place outside of your vehicle. Then, if you ever discover yourself locked out of your vehicle, you'll be able to call the technician or company who installed the system, and they'll provide you with the code. If you are unable get in touch with them, you can seek out an authorized dealer. However, this might require verification procedures, and you could be charged additional charges.
Apart from the ease of this system, you can also rely on it to protect your car against theft and help reduce the cost of insurance. Many insurance companies offer lower monthly rates or even financial incentives for installing this anti-theft system.